Should i seal my interlock driveway

Then use your garden hose or power washer to wash them down. Be sure to do a complete and thorough job! Step 3: Pour the water and detergent solution over your pavers. Next, let the solution sit on your pavers for about 20 minutes or so. This will allow the solution to penetrate the dirt, helping it to lift and wash away easier. Once the 20 minutes have passed, scrub the solution deeper into the pavers using your scrubbing brush or a broom with stiff bristles.

If you find any stubborn stains, clean them with the brick or concrete stain remover. Just be sure to follow the instructions carefully. If you notice that any joints need extra sand, fill them by:. It will make it so much faster. Depending on the stone that you have, you will need at least 10 bags of polymeric sand for sq ft. If the women don't find you handsome, they should at least find you handy.

I think 5 years weed free is overly optimistic, regardless of who will do it. I asked him how long would it take, said 1 day with 2 guys. This is probably one of the easiest things to do in a home. Get a power washer, get some bags of polymeric sand.

Anyone recommend a decent place to get polymeric sand? Well worth the extra cost. They must have a huge mark up on it and not give a schitt about how their customers make out. It is not rocket science. I ruined some old running shoes doing it. Either wear rubber boots or just rubber sandals you can hose down after. How can I fix it? Would sealing it fix it?

What type of jointing material did you use…regular sand or polymeric sand? If you used regular sand, you might want to consider rejointing. You would use a low-PSI pressure washer with a rotating tip to remove the sand from the joints, blow off the debris, and let it dry completely typically 24 hours.

Then, refill the joints with polymeric sand. Allow to cure for 30 days and then seal. We are about to get Belgard pavers installed and have been told conflicting information about when to have the sealer put on.

We live in Florida. One said to wait three to four weeks. The other said we should have it put on the next day. Which is the better approach? When it says to wait 30 days to avoid trapping moisture, is that referring to moisture held in the pavers during storage before installation? Like what if it rains 14 days after installation? Does rainwater evaporate quicker so this is referring only to the water that has permeated the pavers deeper down? Water is used to activate the jointing sand.

It takes the joints a couple of days to harden and 30 to cure. What product do you recommend to kill and clean the black mold off of the pavers and sand between? A lot of products that treat mold are terrible for pavers and can actually discolor them.

Techniseal Organic Stain Remover can safely treat and remove mold without damaging the pavers. Hello, I live in Seattle and I understand I need to wait 30 days before I can seal my driveway and patio pavers that were just installed.

But we are entering the cold, rainy season. Should I just wait until Spring? You may want to wait. You definitely want them to be good and dry and for the temperature to be over 55 degrees. When you do seal them, you can clean them with Techniseal Paver Prep to get rid of any dirt that accumulated since installation and for maximum penetration of the sealant. I just had a contractor install a large patio and pool deck with Catalina Grana pavers. In many locations he used the butt end of a hammer handle to set the pavers, leaving white marks where they were hit.

The pavers do not yet have joint sand applied. The contractor says that sealing with a matte finish sealer will eliminate all the marks. Do you have a suggestion? Your question has been forwarded to our customer care center. They will reach out to you shortly to get additional information and make recommendations for a course of action.

We just had a paver patio and pool installed. They did not seal the pavers. I believe the the installers splattered pool shock on the pavers.

Which product would be the best to clean that? Plan to seal the pavers in Spring. Your pavers definitely need to be sealed. Hopefully, the stains you are talking about are efflorescence and not from the pool shock, as shock contains chemicals that could potentially discolor unsealed pavers. Efflorescence is a natural process that can happen with when the salts inside of the pavers migrate to the surface.

Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Contact Us. Should all concrete pavers be sealed? Do all paver sealant brands offer the same basic protection? Is any one paver sealant finish more protective than another? How long should new pavers cure before they are sealed for the first time? Is there a prep process before applying paver sealant? How long should pavers dry after being cleaned and prepped? What are the ideal weather conditions for sealing?

How often should paver sealer be reapplied? Once you start working, keep working. An application sprayer available at any hardware store makes it easier to work faster. Apply paver sealant to saturation. Get the pavers good and wet to make sure all crevices are covered. Then use a dry roller to soak up the excess to avoid lines and drip marks. When in doubt, hire a professional. To find qualified contractors in your area, visit the Belgard contractor locator. Tags cleaning and sealing patio pavers cleaning and sealing pavers paver maintenance paver sealants.

Should we use water based or oil based sealer on our lani pavers. We want a matt finish. Di you seal the pavers before or after the joints are poly sanded. Thank you, I am looking for the longest lasting, most protective. There is no techniseal dealer in Any ideas? Will let you know how it goes. Is the dirt erosion from the joints or another kind of dirt?

I will reach out to the Techniseal team to see what the best option would be and report back. We forwarded your question to the Techniseal technical support team. Leave a Reply Cancel reply Your email address will not be published. For best results enter the ZIP code where your project is located. Belgard products are manufactured regionally.

Change Location.